Options
Damaged Laptop Screen, Anything A Can Do?
IvanIV
Posts: 30,310
Forum Member
✭✭✭
I managed to damage my old laptop's screen by stepping on it (don't ask) and now there's an area ~ 3x10 cm in the upper left corner that is dead. It's mostly white with one grey area inside and a few colour vertical lines going through it. Pressing on it shows some change, but there's no improvement. Apart from replacing the screen is there anything I could try to make it better? Some programmes that would change colours or anything else? Thanks. If everything fails I guess I will consider a screen replacement, but I want to try first before throwing money on it.
0
Comments
There are changes, it looks like some liquid moving around in that part, but no improvement.
There is a chance it could be a connection problem in which case you might get it back by striping the lid down and reseating everything to make sure it is all in it's proper place. But I have my doubts that it would be that simple.
If you tell us the make and model of the laptop someone may know of a guide to getting into the screen. For example a lot of Dell machines have service manuals available on the Dell website that show you how to take it apart and put it back together again. And you might find a YouTube video showing how to do it.
As it is an HP laptop you can get a Service Manual (not User Manual) from here ...
http://h20000.www2.hp.com/bizsupport/TechSupport/ProductRoot.jsp?lang=en&cc=uk&taskId=135&docIndexId=64902&contentType=SupportManual
Which will show you exactly how to take it apart and also give you the part numbers required.
Your best bet would be to buy a damaged laptop off Ebay (with good screen of course).
Good luck, it will be easier than you think.
Remove the battery and make sure the power cable is NOT attached.
Put the laptop on a flat stable surface and push the screen back as far as it will safely go (in most case it will go flat).
Carefully prize off the strip of plastic above the keyboard that holds the power button etc.
Carefully prize off the hinge covers.
Now identify and remove the screws that hold the screen hinges in place.
You should see the ribbon cable that connects the screen to the motherboard. Very carefully prize the small plastic clip open that holds the ribbon cable in place (this is very easy to break).
Pull out the ribbon cable and remove the screen.
Fit the new screen and just reverse the above to connect and secure it in place.
However, newer laptops have a one piece top cover over the motherboard. This can be a bit of a pain to remove as it normally involves removing the keyboard and/or in most cases even removing the bottom, finding the screws that hold the top cover in place and removing them, turning the laptop back over and then laying the screen flat etc. If that turns out to be the case get yourself a sheet or two of A4, draw a rough schematic and mark the screws (and anything else you need to disconnect or remove) on it so you know what goes where when it comes to putting it all back together.
Follow Alan's advice and get the service manual, read it a few times to ensure you understand the procedure. Check YouTube for videos on how to do it too.
New screens can be expensive, so check out Ebay. You normally find quite a few laptops that are broken, but may have intact screens and you even find sellers who take such laptops apart and sell the parts on their own too. The service manual will give you the correct part number, and often you don't need to buy the exact same model of laptop as the same screen might be used in other machines, sometimes even from other manufacturers. It;'s the part number that's important, not the model number of the laptop.
After all of that, it's fairly easy so don't be put off, you just might have to take your time.
You'll find videos on YouTube
Ooooh, I wouldn't do that.
You'd be very lucky to find a non-working laptop where the seller is willing to guarantee that the screen is still functional.
Far safer to just bite the bullet and buy a new screen if possible.
A new LCD panel should only cost between £50 and £90 so it's not the end of the world.
Use a screen utility to make the damaged area redundant.
When web browsing resize the box to omit the damaged section.
Thanks, I did try that, it's still annoying. Given the price of a new panel I see a bit of DIY coming
This is good advice.
I've repaired a couple of HP laptop screens recently and both of them had different versions of the screen available.
If there's a chance this might be an issue it's likely that the advert will alert people to the issue by saying you need to confirm if your screen has the connector in a certain place or if it has a certain shape circuit-board or whatever but some unscrupulous sellers will deliberately avoid mentioning this in the hope of increased sales.
I'd suggest that when you take the screen apart you take lots of photo's, make notes of what type of screws (chrome/black) go where and generally treat it far more seriously than you think you need to.
You might think you'll be able to put it together again by memory but then murphy's law will be invoked, your replacement screen will get lost in the post, the replacement will be delayed and then, when you finally come to fit the new screen 3 weeks later, you won't remember how to do it properly.
Also, Top Tip: It's pretty common that you need to peel off little adhesive pads covering screws on the screen.
after you've peeled them off, stick them to the screen bezel, somewhere near where they're supposed to go, so you don't lose them or get the adhesive covered in dust.