As I'd said previously working fine here,checked version & it's 1.02.29 Surely this must be a problem with the users receiver!
HD-FOX-T2 ... TV Portal not working anymore.
2 of 2
I have just checked on my HD Fox T2 (v1.02.28) connected directly to my BT router and the iPlayer works ok.
A few straw-clutches:
Can you check with connection directly into your router and not via the Homeplugs?
Perhaps the connection checks internet speed and yours is a bit down at the moment.
You could downgrade your software to v28 to see if any glitches have got into your software. You can then upgrade later. Means a retune though.
Martin
A few straw-clutches:
Can you check with connection directly into your router and not via the Homeplugs?
Perhaps the connection checks internet speed and yours is a bit down at the moment.
You could downgrade your software to v28 to see if any glitches have got into your software. You can then upgrade later. Means a retune though.
Martin
Originally Posted by iiyama17:
“I'm 30 minutes down the road from you near Warrington. You'd be welcome to plug it into mine if you're really stuck.
”
“I'm 30 minutes down the road from you near Warrington. You'd be welcome to plug it into mine if you're really stuck.
”
Thanks for the offer ... but I don't have a car.
Originally Posted by MartinOnline:
“Can you check with connection directly into your router and not via the Homeplugs?
”
“Can you check with connection directly into your router and not via the Homeplugs?
”
I would if I could. The router is downstairs in the front room, while the Humax box is upstairs here in the back room.
Originally Posted by MartinOnline:
“Perhaps the connection checks internet speed and yours is a bit down at the moment.
”
“Perhaps the connection checks internet speed and yours is a bit down at the moment.
”
Well, all my other devices can go online fine. Streaming from BBC iPlayer and/or Netflix on my Xbox is near flawless.
It'll have to wait until later, as I'm having my broadband switched over from O2 Broadband to Plusnet FTTC today.
Originally Posted by MartinOnline:
“You could downgrade your software to v28 to see if any glitches have got into
your software. You can then upgrade later. Means a retune though.
Martin”
“You could downgrade your software to v28 to see if any glitches have got into
your software. You can then upgrade later. Means a retune though.
Martin”
I think that'll be the next option.
to the OP , I have the same box and the same problem, I too used mine successfully at one time, havent used it for a while, now get the same problem as op, tried factory restore etc, no use, I will explore and come back if I find an answer.
Originally Posted by ffawkes:
“to the OP , I have the same box and the same problem, I too used mine successfully at one time, havent used it for a while, now get the same problem as op, tried factory restore etc, no use, I will explore and come back if I find an answer.”
“to the OP , I have the same box and the same problem, I too used mine successfully at one time, havent used it for a while, now get the same problem as op, tried factory restore etc, no use, I will explore and come back if I find an answer.”
I have the same setup (HD FoxT2 plus Homeplugs) working fine. However, I have had a glitch in the past where, although it said the network was connected, it needed reconfiguring by DHCP before the portal would load. Only happened once and been OK for months since. Grasping straws, but you never know....
Mike
Originally Posted by pilgrim42:
“I have had a glitch in the past where, although it said the network was connected, it needed reconfiguring
by DHCP before the portal would load. Only happened once and been OK for months since.
”
“I have had a glitch in the past where, although it said the network was connected, it needed reconfiguring
by DHCP before the portal would load. Only happened once and been OK for months since.
”
Thanks, but that would also mean having to reconfigure the network back to DHCP and taking our website offline.
Originally Posted by Bob1942:
“As I'd said previously working fine here,checked version & it's 1.02.29 Surely this must be a problem with the users receiver!”
“As I'd said previously working fine here,checked version & it's 1.02.29 Surely this must be a problem with the users receiver!”
Still working 100% here, my motto "If it's not broke don't meddle"
Originally Posted by Bob1942:
“Still working 100% here, my motto "If it's not broke don't meddle"”
“Still working 100% here, my motto "If it's not broke don't meddle"”
Bob, I'm sure the OP is very happy that yours is working fine. But what use to him is it for you to keep carping on about it?
My motto "If you've nothing of use to say, then keep quiet."
Originally Posted by iiyama17:
“Bob, I'm sure the OP is very happy that yours is working fine. But what use to him is it for you to keep carping on about it?
My motto "If you've nothing of use to say, then keep quiet."”
“Bob, I'm sure the OP is very happy that yours is working fine. But what use to him is it for you to keep carping on about it?
My motto "If you've nothing of use to say, then keep quiet."
”
My point is if the majority don't have problems then it must be his machine setup.
As for carping on the last I heard we still are in a relatively free speech society
Originally Posted by Bob1942:
“My point is if the majority don't have problems then it must be his machine setup.
As for carping on the last I heard we still are in a relatively free speech society”
“My point is if the majority don't have problems then it must be his machine setup.
As for carping on the last I heard we still are in a relatively free speech society”
He knows he has a problem - that's why he's on here trying to find a solution.Have your comments helped him at all? No.
Originally Posted by iiyama17:
“He knows he has a problem - that's why he's on here trying to find a solution.Have your comments helped him at all? No.”
“He knows he has a problem - that's why he's on here trying to find a solution.Have your comments helped him at all? No.”
At one point he didn't seem decided where the problem is,my comment would I hope lead him closer to his receiver & not a general problem,next time I'll ask your permission but don't hold your breath!
Originally Posted by Bob1942:
“At one point he didn't seem decided where the problem is,my comment would I hope lead him closer to his receiver & not a general problem,next time I'll ask your permission but don't hold your breath!”
“At one point he didn't seem decided where the problem is,my comment would I hope lead him closer to his receiver & not a general problem,next time I'll ask your permission but don't hold your breath!”
Bob, I wouldn't dream of it
2 of 2
